Home
Configuring
Use this information to configure your network, users, servers (including Web servers), directory services, security, messaging, widgets and live text, and server clusters.
Configuring a network
This section presents the planning concepts and setup procedures necessary for a successful HCL Domino® deployment over a network. It provides information on network protocols from a Domino perspective but does not attempt to provide general network information.
Setting up Domino® servers on the network
Before and after installing a Domino® server, perform required tasks.
Server setup tasks specific to TCP/IP
After you run the Domino® Server Setup program, complete these procedures:
Changing the TCP/IP connection-time-out interval
You can increase the number of seconds that HCL Domino® waits before terminating a connection attempt. For example, increasing the time-out interval is often necessary on a server that dials up other Domino servers. The default time-out interval is 5 seconds.

Configuring
Use this information to configure your network, users, servers (including Web servers), directory services, security, messaging, widgets and live text, and server clusters.
- Configuring a network
  This section presents the planning concepts and setup procedures necessary for a successful HCL Domino® deployment over a network. It provides information on network protocols from a Domino perspective but does not attempt to provide general network information.
  - Domino® and networks
    A variety of client systems can use wireless or wired technology to communicate with Domino® servers over local area networks (LANs), wide area networks (WANs), and metropolitan area networks (MANs). For example, Notes® workstations and Domino servers use the Notes remote procedure call (NRPC) protocol running over the LAN's network protocol to communicate with other Domino servers. Other client systems, such as Web browsers, Internet mail clients, wireless application protocol (WAP) devices, and personal information management (PIM) devices, can also communicate with Domino servers.
  - Network security
    Physical network security is beyond the scope of this documentation, but you must set it up before you set up connection security. Physical network security prevents unauthorized users from breaking through the network and using one of the operating system's native services -- for example, file sharing -- to access the server. Physical network security also comes into play when any data is exposed, as the potential exists for malicious or unauthorized users to eavesdrop both on the network where the Domino® system resides and on the system you are using to set up the server.
  - Setting up Domino® servers on the network
    Before and after installing a Domino® server, perform required tasks.
    - Setting up Notes® named networks
      The Domino® Server Setup program automatically places all servers that are in a Domino domain and that run the same network protocol in the same Notes® named network (NNN). In the Server document, the setup program assigns each NNN a default name in the format portname network.
    - Fine-tuning network port setup on a server
      After you install and set up a Domino® server, review the list of network ports that were enabled by the Server Setup program. Unless you customize network settings during setup, Domino enables ports based on the current operating system configuration. To conserve system resources, disable the ports for protocols that you do not need.
    - Server setup tasks specific to TCP/IP
      After you run the Domino® Server Setup program, complete these procedures:
      - Setting up a secondary name server
        To ensure that the Notes® Name Service is always available to Notes users, assign a secondary name server in users' Location documents.
      - Changing the TCP/IP connection-time-out interval
        You can increase the number of seconds that HCL Domino® waits before terminating a connection attempt. For example, increasing the time-out interval is often necessary on a server that dials up other Domino servers. The default time-out interval is 5 seconds.
      - Enabling support for IPv6 on a Domino® server
        You can enable support for IPv6 on a Domino® server that runs the IMAP, POP3, SMTP, LDAP, or HTTP service.
      - Reordering multiple server ports for TCP/IP
        If a Domino® server has multiple Notes® network ports for TCP/IP, the order in which these ports are listed in the NOTES.INI file and the Server document affects how other servers and workstations connect to this server. The Ports setting in the NOTES.INI file determines which port a workstation or server tries first. In the absence of other settings that bind an NRPC, POP3, IMAP, SMTP, or LDAP service to an IP address, all of these services will try to use the port listed first in the NOTES.INI file.
      - Binding an NRPC port to an IP address
        By default, all TCP/IP-based services on an HCL Domino® server listen for network connections on all NICs and on all configured IP addresses on the server. If you have enabled more than one Notes® network port for TCP/IP (TCP port for NRPC) on either a single Domino server or a Domino partitioned server, you must associate the NRPC ports and IP addresses by binding each port to an address.
      - Binding an Internet service to an IP address
        If the HCL Domino® server has multiple HCL Notes® network ports for TCP/IP (NRPC ports) and the server is also hosting the SMTP, POP3, IMAP, LDAP, or Domino IIOP (DIIOP) service, you must specify the NRPC port that you want the service to use in the NOTES.INI file. If you do not specify an NRPC port for an Internet service, by default the service will use the port listed first in the Ports setting in the NOTES.INI file. You can specify the same NRPC port for multiple Internet services.
      - Assigning separate IP addresses to partitions on a system with a single NIC
        If you use a single NIC with multiple IP addresses, you must complete additional configuration instructions, which are based on your operating system, for each server partition. Using separate IP addresses with a single NIC can have a negative impact on the computer's I/O performance.
      - Configuring a partitioned server for one IP address and port mapping
        To configure server partitions to share the same IP address and the same NIC, you use port mapping. With port mapping, you assign a unique TCP port number to each server partition and designate one partition to perform port mapping. The port-mapping partition listens on port 1352 and redirects HCL Notes® and HCL Domino® connection requests to the other partitions.
      - Changing a TCP or TLS port number
        The following sections describe the TCP ports that HCL Domino® services use and provide guidelines should you ever need to change these ports.
      - Confirming that TCP/IP is configured properly
        Before you can use TCP/IP for communication, confirm that the configuration is properly set up.
- Configuring users and servers
  Topics in this section describe how to set up users and servers.

Changing the TCP/IP connection-time-out interval

You can increase the number of seconds that HCL Domino® waits before terminating a connection attempt. For example, increasing the time-out interval is often necessary on a server that dials up other Domino® servers. The default time-out interval is 5 seconds.

Procedure

From the Domino® Administrator, click the server for which you want to change the time-out interval.
Click the Configuration tab.
From the Domino® Administrator's Tools pane, choose Server > Setup Ports.
Select the TCP/IP port.
Click TCPIP Options and enter a number.

Note: Unless the connection is over a dial-on-demand ISDN modem, remote bridge, or router, it is best to enter a number no greater than 10, as the HCL Notes® client or Domino® server will not retry the connection until the timer has expired.
Click OK.