Deploying clients from the console
Prerequisites:
Before deploying the BigFix clients from the Client Deploy Tool Wizard, ensure that you locate and activate globally the following analyses:
ID | Name |
---|---|
204 | BES Component Versions |
2814 | Collect BES Client Deploy Tool Reports |
From the BigFix console, click
.The Client Deploy Tool Wizard will guide you through the deployment of the BigFix clients.
- Select one or more assets in the view.
- Right-click them. A menu opens.
- Click Install BigFix Client.Note:
The displayed Client Deploy Tool Wizard already contains the following prefilled information:
- The names of the assets selected in step 1.
- The selection of the operating systems installed on the assets selected in step 1, found by the Nmap scan run on the assets.
- Click Add Targets.
- Enter the host name or the IP address of the target computers.
- Select the target computers displayed on the list.
- Click Set Credentials.
- Enter the user name and password needed to access the target computers.
- Starting from Version 9.5.10, you can select the Use Key
File check box if you use a private key file, supported by the
SSH authentication method, instead of a password. You can also specify a
passphrase if it was specified when generating the private key. Only ASCII
characters are supported. Use a private key file in PEM format. Note: The SSH authentication method is not supported to install Windows target clients.Note:
The user, configured to access the target computer by using the SSH key authentication, must be one of the following:
- root
- a user configured to run SUDO without a password.
Note: If you enabled FIPS mode and you use SSH key authentication with passphrase to install the clients, ensure that your certificates are generated using FIPS compliant algorithms.Note: The only SSH algorithms supported to access the target computers through the SSH key authentication are ssh-rsa and ssh-dsa. - Click Next to proceed to the Select Deployment Point page.
- Select the target computers displayed on the list.
- Click Select Deployment Point.
- Select a deployment point from the list.Note:
The deployment points displayed by this list are a set of:
- All computers on which the Client Deploy Tool can be installed, and which are relevant for the Fixlet "Install/Update BigFix Client Deploy Tool Version 9.5". Remove 'yes' from the 'Is Preferred' filter to have the list of all computer selections available.
- All computers on which a standalone Client Deploy Tool (any Version) is installed. If an older version is found, the Client Deploy Tool will be upgraded to Version 9.5.7.
- All computers with a BigFix Console Version 9.5.7 or later.
- Click Next to proceed to the Set Deployment Point Credentials page.
- Select the deployment point displayed on the list.
- Click Set Credentials.
- Enter the credentials needed to access the deployment point.
- Click Next to proceed to the Set Advanced Settings page.
- Select the operating systems to be deployed, if not already prefilled by the results of the Nmap scan run on the assets.
- Select the client version to be installed on your target computers.
- Select the Show advanced settings check box.
(Optional) In the "Custom Settings" section, add a list of custom client settings to apply to each client that will be deployed by the Client Deploy Tool.
You can input these settings in either a table or a text box. If you use the table, add a row for each setting, then enter its name and value in the respective columns. If you use the text box, add a new line for each setting, then enter its name and value in the format "name=value".
(Optional) In the "Proxy Settings" section, if the clients to be deployed must communicate through a proxy, enter the following information:- Address
- The host name that is used to reach the proxy.
- Port
- The port that is used to communicate with the proxy.
- Username
- The user name that is used to authenticate with the proxy if the proxy requires authentication.
- Password
- The password that is used to authenticate with the proxy if the proxy requires authentication.
(Optional) Starting from Version 9.5.10, there is also a section where you can enter a custom installation path for the Windows target computers.
- Click Next to proceed to the Deploy Clients page.
- Review the following summary information displayed by the wizard:
- The list of all target computers on which the BigFix client will be installed. The user names needed to access the target computers. The deployment point that will be used for each target computer.
- If new deployment points were specified, a list of the deployment points on which the Client Deploy Tool will be installed.
- On each deployment point, the BigFix client packages that will be downloaded, if not already present.
- If the summary information is correct, click Deploy.
After clicking Deploy, the Client Deploy Tool Dashboard displays the details of your BigFix client deployments. For more information about the dashboard, see Viewing the deployment results in the dashboard.